Because this part is meant as a replacement, the cam latch or lever isn't provided. The idea is that the old one would be reused. Camco does offer the same product that would include both a straight and an offset latch, part # CAM44323. The threaded barrel is 7/8 of an inch thick, and would be compatible with most RV storage compartment doors. view full answer...
I attached a diagram that shows how the BrakeRite Actuator part # T4813100 gets wired to a trailer. If you have only one battery on your trailer you'd need to run all of the battery connections to the single battery and you'd be set.
The newest version of this is the Titan BrakeRite I Plug and Play Electric-Hydraulic Actuator Kit # T4813102. view full answer...
It's probably a weak ground. What I would recommend trying is making sure that the main ground wire of the trailer wiring is connected to a clean metal surface on the trailer frame since the Lippert jack part # LC643589 grounds through the mounting hardware. view full answer...
For your 2010 Coleman Niagara, the dimensions you gave are a big help. There isn't a perfect fit for the current setup, so you will need to use what is called an outrigger. You can use the Flexco Manual Pull-Out Steps for RVs - Double - 8" Drop/Rise - 20" Wide - 300 lbs # SMFP-2120 along with the Lippert Outriggers for Manual RV Steps # LC301704 to give you the correct fit and stability. You will use hardware # LC118155-72 to make them compatible.
Note--You may use an Outrigger on... view full answer...
The best protecting and fitting cover that fits your 2018 Rockwood Ultra V camper that measures 30 foot 3-1/2 inches long is the Adco Olefin HD cover part # AD27ZR. The front of this cover has adjustment straps that you can use to taper in the front of it to match the V-nose setup of your trailer. This offers the best protection in all climates including snow, installs the easiest, and has access panels on the sides so that you could get into the camper when stored if needed. view full answer...
What you have appears to be a standard puck light which you could use the part # 277-000343 as a replacement for if it's 3 inch in diameter like it looks like. We also have 4-1/2 inch size like part # 277-000344 but it does look to me like you have the 3 inch size. view full answer...
The Adco Olefin HD All-Climate + Wind RV Cover for Travel Trailer - Up to 34' Long - Gray # AD59ZR uses cinch ropes at front and rear of cover remove slack and reduce billowing and snug up to the shape of your 2017 Forest River Rockwood Windjammer 3008W Travel Trailer. Weighted straps with buckles secure the cover under the trailer to prevent the cover from blowing off in the wind so you shouldn't need to use any additional straps or ropes to secure this cover. view full answer...
The MORryde StepAbove RV Steps # MR98RR only have provisions for mounting the Handrail # MR83AR on the left side of the steps. This is as most doors are on the passenger side and open towards the right which would cause them to contact the door. If you have a door that opens to the left I recommend using the Lend-a-Hand Extra Large Folding Grab Handle # AM-533. This oversized handle will extend 25-1/2" to make entering and exiting your camper easier. view full answer...
The closest thing we have to what you are looking for is the Dometic Part Timer RV Toilet part # DOM47FR that is the darker color, has the sprayer, and has the slow lid close. view full answer...
We do have an adjustable-width RV trailer hitch receiver that will work for your I-beams spaced 68-1/2 inches apart, though the 13704 you mentioned is only for frames up to 66 inches apart. In the past it was for slightly wider frames but the manufacturer updated the dimensions.
So because your I-beams are 68-1/2 inches apart, the correct hitch for your trailer is the Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703.
This uses brackets that and 1/2 inch bolts to... view full answer...
I looked up the Blackstone Griddle online and seen that it accepts a 1 lb propane bottle therefore it would have a disposable cylinder fitting on the end. If that is the case then you can use the MB Sturgis Quick Disconnect Propane Hose part # 100476-120-MBS to attach this to the female quick disconnect port on your trailer.
However, this option most likely will not work for you because the quick disconnect port on your trailer is already ran through the propane regulator. This hose will... view full answer...
Unfortunately, just knowing that the trailer runs off of 30 amp service won't tell me what the converter's amperage rating is. The converter is taking the AC service that your trailer has when connected to shore power and converts it into DC to recharge the battery. DC power is 1/10th of AC power so you could have a converter that ranges from 20 amps all the way up to 90 amps.
Most trailers typically have a converter rated around 30 amps to about 45 amps. The wire gauge used for your... view full answer...
Since this wiring harness can be hard wired in you are correct, the # HM40975-11998 could be used on your 1987 GMC Sierra. It sounds like you already had a 7-way at the back and just needed to replace it so there should be no need for additional wiring. You will just need to match the wires up with with the correct functions and mount the connector with the included bracket. view full answer...
The correct set of SolidStep Manual Fold-Down Steps for a 2018 Forest River Rockwood Windjammer with 28" doorway and 36" entry height is indeed part # LC791574. This option also will give you some extra margin for the steps when parking on unlevel terrain. view full answer...
The wiring of the Exterior LED Utility Light # M337FR that you referenced is pretty basic. It has three wires, one for power, one for ground, and one for neutral. We have spoken with M-3 and they informed us that the light follows EU Wiring Specifications so the power should be brown, the neutral should be blue, and the ground should be green with a yellow stripe.
The power source would need to be 110 AC power like what a house would have. view full answer...
The gear that you're talking about on your MaxxFan 4401K is the operator mechanism. For a replacement you need the # MA10-20281K-1AF. view full answer...
The Solera 21' Sand Fade RV Awning Roller and Fabric, # LCV000334447, you referenced should fit the awning arms on a Dometic awning. Lippert cannot confirm the fit as they have not installed these parts, but they can confirm this awning fits industry standards, so you shouldn't have any issue. This awning roller and fabric will fit an assembly designed for 21 foot long awning with a 8 foot extension from the RV. This fabric is anti-scuff, anti-mildew and transitions from sand to white with... view full answer...
The TorkLift GlowStep Revolution Scissor Steps # TLA8004 that you referenced are designed to fit the standard RV step areas with the bracket kit part # TLA8022. There will most likely be some drilling though since these do install in a slightly different way that standard steps.
The feet of the steps are adjustable in height pretty easily so if you somehow ended up on unlevel ground enough to call for it you could adjust the feet. In general most campsites are level enough for these to... view full answer...
Go To Results